Skip to content
ContractorsRanked

How much does a water heater replacement cost in Plain City, UT?

US national rangeUpdated Prices checked October 20262 sources

A water heater replacement costs $882 to $1,826 nationally, typical $1,348. We have no documented price index for Plain City for this job, so this is the US national range from HomeAdvisor, checked October 2026.

US national range, not adjusted for this city

Low
$882
Typical
$1,348
High
$1,826

Get water heater replacement quotes in Plain City

Water heater replacement cost in Plain City, UT

We have no documented price index for Plain City for this job, so the table shows the US national range.

Water heater replacement cost in Plain City, UT
EstimateLowTypicalHighBasisChecked
US national range$882$1,348$1,826Per unit, installed (unit plus labor); typical range of customer-reported jobs (HomeAdvisor)October 2026

Water heater replacement cost by type or size

US national figures in USD, as published by each source.

Water heater replacement cost by type or size
Type or sizePrice (USD)Source
40-gallon tank, installed$550 to $2,300Fixr
50-gallon tank, installed$700 to $2,500Fixr

What drives the cost of a water heater replacement

  1. Type of heater

    Tank, tankless, heat pump and solar units differ widely in price.

  2. Tank size

    A 50-gallon tank costs more than a 40-gallon tank.

  3. Fuel source

    Switching fuel, or adding gas lines or electrical circuits, raises the cost.

  4. Venting and code upgrades

    Power venting, expansion tanks and code fixes add parts and labor.

  5. Labor and access

    Labor is about half the total; tight closets and attics take longer.

Permits and what's included in Plain City

Permit note

Most areas require a plumbing permit. A standard permit runs about $25 to $300, and a separate gas permit, if needed, about $50 to $300.

Rules are set locally; confirm with Plain City’s building department.

What’s usually included

  • The new water heater
  • Labor to disconnect the old unit and connect the new one
  • Removal of the old unit (often included; confirm on the quote)

Scopes vary. Get the scope in writing on every quote.

Get water heater replacement quotes in Plain City

Tell us about the job and we will pass it to local pros. Asking for quotes never changes how we rank anyone.

Two short steps: your name, then how to reach you. Free, and it never changes anyone’s rank.

Top-ranked plumbers in Plain City

The top 3 of 137 plumbers we rank for Plain City, UT, by CR Score. Paid placement never changes rank.

  1. #1
    Mike Bachman Plumbing
    CR Score 654.8from 2,213 Google reviews
  2. #2
    S & B Plumbing
    CR Score 624.7from 212 Google reviews
  3. #3
    City Creek Plumbing
    CR Score 615.0from 573 Google reviews

See all ranked plumbers in Plain City

How to check a plumber's license in Utah

In Utah, Utah Division of Professional Licensing (DOPL) licenses Plumbing work: water supply, drain, waste and vent piping and fixtures.

  1. Check that the status is active and the name matches the contract or truck.
  2. Ask for proof of insurance before work starts.

No chip usually means we have not matched a state record yet. Check the lookup yourself before you hire.

Guide checked October 2026. How we verify licenses

Water heater replacement cost in Plain City: questions

How much does a water heater replacement cost in Plain City, UT?

A water heater replacement costs $882 to $1,826 nationally, typical $1,348. We have no documented price index for Plain City for this job, so this is the US national range from HomeAdvisor, checked October 2026.

Do I need a permit for a water heater replacement in Plain City?

Most areas require a plumbing permit. A standard permit runs about $25 to $300, and a separate gas permit, if needed, about $50 to $300. Rules are set locally, so confirm with Plain City’s building department.

What affects the cost of a water heater replacement?

Type of heater: tank, tankless, heat pump and solar units differ widely in price. Tank size: a 50-gallon tank costs more than a 40-gallon tank. Fuel source: switching fuel, or adding gas lines or electrical circuits, raises the cost. Venting and code upgrades: power venting, expansion tanks and code fixes add parts and labor.

How many plumbers serve Plain City?

We rank 137 plumbers for Plain City, UT by CR Score. Get at least three written quotes for the same scope.

What is usually included in the price?

The new water heater; Labor to disconnect the old unit and connect the new one; Removal of the old unit (often included; confirm on the quote). Always get the scope in writing on the quote.

Sources

Checked October 2026. Figures are estimates, not quotes.

  1. HomeAdvisor: Water heater installation cost · page updated June 17, 2026 · checked October 2026Primary source. Used for: Low, typical and high; drivers; permit.
  2. Fixr: Water heater installation cost · page updated January 27, 2026 · checked October 2026Used for: Prices by tank size; cross-check: $900 to $3,000, average $1,400 for a gas tank.
These are published estimates, checked October 2026. They are not quotes. Typical range shown: $882 to $1,826. Editorial policy

Related pages

More cost guides for Plain City